13559553569

泉州聯進機械有限公司

QUANZHOU LIANJIN MACHINE CO., LTD

自

動

沖

床

使

用

說

明

Hydraulic Automatic

Rubber Die Cutting Machine Usage

用途：根據刀模裁斷出需要的橡膠片樣式    

特點：1.不漏壓！不漏油！零事故！

          2.配置安全閥，安全閥一打開馬上停止運作。

使用說明：

公共設備電力：電壓380V,50Hz。

主電源線：2.5平方毫米  三芯線

1. 油箱的油保持幹淨，以免損壞油路的配件。

2. 加46#  液壓油顯示油表至80%。液壓油需每年更換一次。

3. 先馬達啓動，按上升下降5-6次，再按自動。

4. 按照鞋模高度調整氣缸高低開關和油馬達的送料時間長短。

5. 調定件數，按自動開關。

6. 如發現膠片有時長時短

A.要檢查譯碼(ma)器的傳動齒輪是否有松動，齒輪間隙是否過大。

B.檢查壓輥兩端彈簧是否過松。

C.檢查傳動鏈條是否松動。

D.進料時膠片一定要通過每一條過橋輥。

E.調整進料壓力閥和節流閥。

F.如發現有阻料現象，按照上面6中的D解決。并送料一定要平整進入。

7.如發現料有切不斷

A.查看刀模是否平整。

B.調整延長時間。

C.調整壓力閥。

8.油壓之最高使用壓力爲100kg/cm ,一般常用50-70kg.

9.活塞和缸套應保持潤滑油脂，一個星期注油一次（有氣泡時注油）

10.在正常使用過程中故障小，一般多爲保險絲燒掉，操作面闆損壞，電磁線圈損壞，電眼（傳感器）沾粉。

Purpose：According to the knife mold cut out the required rubber sheet style.

Specialty: 1. No leakage in oil or pressure, safe.

                2. It will stop working once the safety valve is open.

INSTRUCTIONS: 

Public equipment：Power: 380V,50Hz.

Host power line:  2.5mm² three -core

1. Keep the oil in tank clean, avoid damaging its accessories.

2. Add the 46# hydraulic oil until oil gauge reach to 80%. The hydraulic oil needs to be replaced once a year.

3. Start MORTOR, press UP and DOWN buttons 5-6 times, and then press the AUTO button.

4. Adjust the cylinder HIGH-LOW button to set the cutting speed and time according to the height of shoe moulds.

5. Set a specific figure for number of units, and then press the AUTO button.

6. If found the rubber cut being long or short unequally.

A. Check whether the transmitting gear of decoder work nomally, whether gear space is too big.

B. Check if the springs at two sides of roller are too loose.

C. Check whether the transmission chain too loose.

D. When feeding, the rubber must be through every gap bridge rollers.

E. Adjust feeding pressure valve & throttling valve.

F. If found any stop-feeding phenomenon, solve it according above 6(D). Feeding must be put into in the same level.

7. If found the rubber could not be cut.

A. Check whether the cutting die is flat.

B. Adjust to elongate the cutting time.

C. adjust pressure valve. 

8. The highest pressure in using is 100kg/cm about hydraulic oil, the nomal one being 50-70kg.

9. Piston & cylinder linner must be keep lubrication by adding oil once a week (when bubble appears)

10. Little fault under normal use, it is ordinary because fuse burned, panel damaged electromagnetic coil damaged, or powder attaches to transducer.